TECHNICAL DATA ATO-56
HIGH HEAT PRIMER
Form: GDH-109
Rev.: 071613
.DESCRIPTION AND USES .
Rust-Oleum
®
High Heat Primer bonds to bare metal and helps
create a smooth surface for top coat application. It is formulated
to prevent rust and is recommended for use on automotive
engines and other automotive surfaces which reach intermittent
temperatures up to 2000°F (1093°C). For maximum protection,
top coat with Rust-Oleum High Heat Paint. High Heat Primer
features an advanced spray system that allows you to spray at
any angle, even upside down for those hard to reach areas. A
comfort spray tip with a wider finger pad reduces fatigue caused
by continuous spraying.
.PRODUCTS .
SKU (12 ounce spray) Description
249340 Gray
..PRODUCT APPLICATION .
PAINTING CONDITIONS
Use outdoors or in a well ventilated area such as an open
garage. Use when temperature is between 50-90°F (10-
32°C) and humidity is below 85% to ensure proper drying.
Do not apply to galvanized metal. Do not use on metal
directly exposed to flames. Avoid spraying in very windy
and dusty conditions. Cover surrounding area to protect
from spray mist.
SURFACE PREPARATION
Wash the surface with a commercial detergent, or other
suitable cleaning method. Rinse with fresh water and dry
with a clean cloth. Remove loose paint and rust with a wire
brush or sandpaper until the metal surface is completely
bare. Lightly sand smooth and glossy surfaces. WARNING:
If you scrape, sand, or remove old paint, you may release lead
dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN
CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,
ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD
ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator
to control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, find out how to protect
yourself and your family by contacting the National Lead
Information Hotline at 1-800-424-LEAD or log on to
www.eps.gov/lead.
..PRODUCT APPLICATION (cont.) .
APPLICATION
Shake can vigorously for one minute after the mixing ball
begins to rattle. If mixing ball fails to rattle DO NOT
STRIKE CAN. Contact Rust-Oleum. Shake often during
use. Hold can 8-12" from surface and spray in a steady
back-and-forth motion, slightly overlapping each stroke.
Keep the can the same distance from the surface and in
motion while spraying. Apply 2 or more light coats a few
minutes apart. Do not use near open flame.
DRY & RECOAT
Dry and recoat times are based on 70°F (21°C) and 50%
relative humidity. Allow more time at cooler temperatures.
Dries to the touch in 30 minutes and dries to handle in 1-2
hours. High Heat Primer may be coated with Rust-Oleum
High Heat Paint anytime after 1 hour. Once dry, High Heat
Paint or Primer must be further cured to increase durability.
Allow High Heat Paint and Primer to dry 2-4 hours before
proceeding to the next steps below. Follow directions
accordingly. Items may emit smoke and harmless odor at
first when heated.
Items Off Vehicle – Bake at 250°F (121°C) for 30 minutes
then allow 30 minutes to cool. Bake at 400°F (204°C) for
30 minutes then allow 30 minutes to col. Bake at 600°F
(315°C) for 30 minutes then allow 30 minutes to cool.
Caution: Be sure not to exceed the heat tolerance of the
least heat tolerant part.
Items On Vehicle – Run vehicle at idle for 10 minutes
then allow 20 minutes to cool. Run vehicle at idel 20
minutes then let cool for 20 minutes. Run vehicle at
normal operating conditions for 30 minutes then allow
vehicle to cool.
CLEAN-UP
Wipe off tip when finished. Clean up wet paint with xylene
or mineral spirits. Properly discard empty container. Do
not burn or place in home trash compactor.
CLOGGING
If the valve clogs, twist and pull off spray tip and rinse in a
solvent such as mineral spirits. Do not insert any object
into can valve opening.
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals